Embedded Hardware Design and Electronics Development
Embedded hardware design and electronics development from one senior team in Silicon Valley: schematic and PCB layout, power and RF, firmware from bare-metal to embedded Linux, and the mechanical design around it, run as a single accountable electronics product development project from architecture through manufacturing transfer.
What embedded hardware design and electronics development actually includes
Embedded hardware design is the work of turning a product idea into a custom circuit board, the firmware that runs on it and the mechanical parts that hold it together, all designed to be built repeatably by a contract manufacturer who has never met you. Electronics product development is the whole arc around that board: architecture, component selection, prototype builds, validation, certification and the transfer to production. At inteRFace R&D we do both with the same senior engineers, and we slow down for the decisions that are expensive to reverse: the microcontroller family, the radio, the power architecture, the certification path. They compound. A design engineered well ships on time and stays on budget; a design that is not, does not.
Most teams that come to us need end-to-end electronics design, from the first block diagram through released production files. Some need one discipline dropped into an existing team: firmware beside an in-house electrical engineer, or layout beside an in-house firmware team. If you are earlier than that, with a sketch and no engineer yet, start with Hardware for Startups, which covers where early hardware companies lose money before a schematic exists.
Electronics: schematic, PCB layout, power and RF
Electronic hardware design starts with the schematic, and we treat it as a deliverable in its own right: every net, every power rail and every connector defined, because the schematic is the contract between the firmware, the board and the manufacturer. Layout follows, placed for signal integrity, thermal behaviour and assembly access. Power trees are designed to survive real loads from battery, USB, solar or mains, and RF front ends get the antenna keep-outs and matching a certification lab will accept. Lights, wireless, sensors, batteries, even XR and medical-adjacent work: bring an early concept or a board that needs improving and we will give you a concrete answer on what it would take to build it well.
Components are selected with availability in mind, with second sources for anything that matters, because the cleanest layout is worthless when its one single-sourced part goes on allocation. Test points, fiducials and a bring-up plan go in at layout time, not when the manufacturer asks. The board work itself, from schematic capture through DFM review, is described on our PCB design service page, and the full sequence to released production files is in our PCB design workflow guide. For a power trace you want to check, the free PCB trace width calculator runs IPC-2221 in both directions and tells you whether the width is manufacturable.
Some boards are specialist work with a page of their own: SDR and RF board design for AD9361, AD9364 and Zynq-based radios and their front ends and clocking, SoM carrier board design for Zynq, i.MX, Jetson and Raspberry Pi Compute Module products, and CubeSat payload electronics for the interface board between a payload and the spacecraft bus.
Embedded firmware: bare-metal, RTOS, embedded Linux and connectivity
Hardware without firmware is a paperweight. We write it at every level a product needs: bare-metal C on small microcontrollers where every microamp counts, FreeRTOS or Zephyr where the device juggles radios, sensors and a display, and embedded Linux (BSP, services, secure boot) where it runs inference, audio or a camera. Connectivity is part of the architecture, not an add-on: BLE with a command protocol your app team can actually implement, Wi-Fi provisioning that works in a real home, and LTE (LTE-M or NB-IoT for low-power devices) where there is no Wi-Fi to join. Over-the-air updates are designed in from the first build, with signed images, staged rollout and rollback, because the first bug found in the field should cost you an update, not a recall. When the firmware is the whole engagement, on a board you already have or one a hardware partner is designing, our embedded firmware development services page covers that scope on its own.
The microcontroller choice constrains everything after it: power budget, certification path, firmware architecture, even hiring. We make it against the product's real constraints, not against whichever dev kit was on the desk. In production we work with STM32, ESP32, Nordic nRF, RP2040 and NXP i.MX, plus embedded Linux on Raspberry Pi, Orange Pi and Rockchip-class SoCs. To pressure-test your choice, the free MCU Selector asks five questions and shows its scoring, and ESP32 vs STM32 vs Arduino for production explains why the right answer for a prototype is rarely the right answer for a product.
Apps and cloud, when the device needs them
Many devices need a companion app and a cloud back end, usually built by the same team: React or Flutter for the app, AWS or GCP behind it. A companion-app MVP with the core flows is about 150-350 engineering hours; a full product with accounts, payments and polish is 300-650 hours. Building the app alongside the firmware matters: the BLE command protocol, the pairing flow and the OTA path are decided across that boundary, and splitting them between two vendors is where connected products lose months.
Mechanical: the enclosure is part of the circuit
In an electronics product the enclosure is never just a box. It sets the antenna keep-out, the thermal path for the power section, the ingress rating, the button feel and whether the board can be assembled by someone with two hands. Our team handles plastic parts, sheet metal, robotic assemblies and the in-between systems where electronics and mechanics meet, designed so every part fits at one unit and at ten thousand, with the manufacturing process respected from the start. That is the difference between a clean DFM review and a six-month tooling redo. The enclosure engineering on its own, around a board from your team or from ours, is described on our mechanical design services page.
One accountable team for embedded hardware design and manufacturing transfer
The most expensive engineering bug is the one that crosses domains: a firmware feature the hardware's power budget cannot pay for, a mechanical detail that fights the antenna, a cloud architecture that forces a power-hungry connectivity choice. Electronics hardware development is a long chain of these decisions, and one roof for electrical, firmware and mechanical engineers removes the back-and-forth. We make those decisions in one room, in one week, and move on.
- Single point of accountability across the stack: no vendor finger-pointing
- Senior engineers in every discipline, not interns wearing senior badges
- Tools and process that scale: Altium / KiCad, SolidWorks / Fusion, Git, CI for firmware
- We work in your tooling, your repo and your review process when needed, or run our own when not
Whole product or one discipline, the work runs through the same phases, each ending in files you could hand to anyone:
- Architecture: requirements, block diagram, microcontroller and radio choice, power budget, certification path and a costed parts list with alternates.
- Electronics and firmware design: schematic, layout, bring-up firmware and a test plan written before the first board arrives.
- Prototype build and validation: boards assembled, brought up and measured against the requirements, then revised while a change is still cheap.
- Design for manufacture and pre-compliance: DFM with the contract manufacturer, test fixtures and an EMC pre-scan before the lab is booked.
- Manufacturing transfer: released production files, work instructions, line test and the first production run, covered on our manufacturing page.
What a first engagement looks like
It starts with a free 30-minute technical call, under NDA if you want one. Book it here and bring the hard question you do not have an answer to. The next step is a bounded Feasibility Review, quoted up front: a written assessment of the highest-risk parts of the design, the experiments that would kill the idea fastest if it is wrong, an architecture and parts list, and a written quote with phases for the work that follows. You can stop there and take the documents with you; you own them either way.
Everything we do is priced in engineering hours; you get a written quote with phases before any work starts. For a planning number, the free project cost estimator turns a scope into a range of engineering hours in minutes, and the AI estimator on the homepage does the same from a paragraph describing your product.
Research and product development, when the science is not settled
Some products still have a research question inside them: a sensor that has not been characterised, or an algorithm that has to fit on a microcontroller. We run research and product development as one track, with the experiments ordered by what would change the design most, so the research phase ends with a decision rather than a report. When the deliverable is the measurement itself, a rig for a university group or an R&D lab, see lab and research instrumentation. For what the whole service actually buys you, and how to compare proposals, read Electronic Product Development Services: What You Are Actually Buying.
What you own
All of it. Schematics and layout sources, Gerbers, drill and pick-and-place data, a costed bill of materials with alternates for anything single-sourced, firmware sources with the build and CI configuration, CAD and the bring-up and test plan. You can take that package to any manufacturer without asking us. We never hold design files, we never take equity, and a mutual NDA is signed before any technical detail is exchanged.
Choosing a partner for embedded hardware design and electronics development? The fastest way to find out whether we are the right one is a free 30-minute call with a senior engineer: book a time. If you would rather start with numbers, run your project through the free project cost estimator and bring the result.
Frequently Asked Questions
What does embedded hardware design and electronics development include?
Four things, run by one team: electronics (schematic, PCB layout, power and RF), embedded firmware (bare-metal, RTOS or embedded Linux, with BLE, Wi-Fi or LTE connectivity and OTA updates), the mechanical design around the board, and the production path: prototype builds, validation, DFM, certification support and the transfer to a contract manufacturer. You receive the released design files at the end of every phase, so the work is yours whether or not we build the next one.
What is the difference between a prototype design and a production design?
A prototype proves the product can exist; a production design proves it can be built a thousand times by people who have never met you. The difference is in the parts (chosen for availability, with second sources), the layout (test points, fiducials, panelisation), the firmware (no USB cable assumed, a factory test mode, field updates) and the paperwork (a costed BOM, work instructions, a line test). We design for production from the first schematic, because a respin at the manufacturer costs more than doing it right at layout.
How do you choose the microcontroller?
Against the product's real constraints: power budget, radios, compute, security, supply chain and the certification path, in that order, not against the dev kit that happened to be on the desk. In production we use STM32, ESP32, Nordic nRF, RP2040 and NXP i.MX, with embedded Linux on Raspberry Pi, Orange Pi and Rockchip-class SoCs, and bare-metal C, FreeRTOS or Zephyr on top. The free MCU Selector at interfacernd.com/tools/mcu-selector shows how we score the candidates.
Do you handle FCC and CE certification?
We design for it and support the product through the lab. FCC and CE outcomes are decided during layout, by ground planes, filtering, board edges and antenna placement, months before anyone books a test, so EMC is reviewed at design time and pre-scanned before the formal session. We prepare the test plan and the documentation and work with the lab on the modular or full radio approvals the product needs. The free certification cost estimator at interfacernd.com/tools/certification-cost shows what the lab work usually involves.
Who owns the intellectual property?
You do, completely. Every schematic, layout file, firmware source, CAD model and document is yours, and you keep the IP and all project data. We never take equity and never make a client dependent on us to manufacture their own product; you can take the package to any manufacturer. A mutual NDA is signed before any technical detail is exchanged, and we can work inside your repositories so the work never leaves your control.
How much does embedded hardware design cost?
By scope. A driver, a feature or a fix on existing firmware is typically 40-90 engineering hours; full product firmware, bare-metal or RTOS, is 90-250; a full embedded Linux system with BSP, services and OTA is 250-600; new or undocumented hardware adds 25-70 hours of bring-up first. Boards are scoped by layer count and complexity. Priced in engineering hours; you get a written quote with phases before any work starts, and our free cost estimator at interfacernd.com/tools/cost-estimator gives you a planning range in minutes.
Ready to talk specifics?
A 30-minute call with a senior engineer beats three rounds of email. Tell us what you're building.